Operator’s manual, John deere, Worldwide commercial & consumer equipment division • Read online or download PDF • John Deere z User Manual. You can find your manual on amazon take a look here Amazon com John Deere Z manual. I hope this was helpful. cheers. Our John Deere Z, Z, Z EZTrak OEM Operators Manual is a brand new original OEM (Original Equipment Manufacturer) manual for this machine.
|Published (Last):||25 July 2004|
|PDF File Size:||19.91 Mb|
|ePub File Size:||2.48 Mb|
|Price:||Free* [*Free Regsitration Required]|
The Engine Exhaust from this product contains jkhn known to the State of California to cause manusl, birth defects or other reproductive harm. Introduction Thank You for Purchasing a John Deere Product We appreciate having you as a customer and wish you many years of safe and satisfied use of manuxl machine.
Z, Z and Z PIN If you need to contact an Authorized Service Center for information on servicing, always provide the product model and identification numbers. Get medical help fast. Tampering with emission controls and components by unauthorized personnel may result in severe fines or penalties. Contact your John Deere Commercial and Consumer Equipment Retailer concerning emission controls and component questions.
Safety Operating Safely This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death.
Be thoroughly familiar with the controls and the proper use of the machine before starting. Disconnect the negative battery cable or remove the spark plug wire for gasoline engines before servicing the machine.
Do not operate the equipment when barefoot or wearing open jlhn. Replace worn or broken parts. Loud noise can cause impairment or loss of hearing. Unplug battery charger before connecting or disconnecting from the battery. Move machine outdoors and provide adequate ventilation. S225 fuel is spilled on clothing, change clothing immediately. If fuel is spilled near machine, do not attempt to start the engine but move the machine away from the area of spillage.
Avoid creating any source of ignition until fuel vapors have dissipated. Check Machine Safety System B Perform safety system check to make sure the electronic safety interlock circuit is functioning properly. Be sure mower is fully raised to the transport lock position, ddeere shown, and insert the pin A in the hole just below the mower deck lift lever B.
Check engine oil level.
Remove grass and debris from engine compartment and muffler area, before and after operating machine. Clean air intake screen. Check area below machine for leaks. Insert the pin A in the proper hole for the desired height of cut.
Turn left blade C as shown. Hold drive belt and turn right blade D as shown. Take measurement for both blades. Rotating blades are dangerous.
Inflate tires to correct pressure. Raise mower deck lift lever, and lock in transport position. Adjust mower wheels to correct height: Adjust mower level, if necessary, by loosening rear nut F on front lift rod. Turn front nut G clockwise to raise front of mower or counterclockwise to lower it. Tighten rear nut after adjustment is complete.
Engine must not crank. If engine cranks, there is a problem with your safety interlock circuit. Testing Seat Switch 1. Move throttle lever up to maximum engine speed.
Raise up off seat. Do not get off machine. Engine and mower blades should stop.
C – Start position – Turn key to start position to crank the engine. Move the motion control levers forward to begin forward travel. Move the motion control levers rearward to begin reverse travel.
To stop travel, move motion control levers back to the neutral position. To turn slightly to the left, push right control lever C further forward than the left control lever D. Gradually move both motion control levers evenly forward A from neutral.
To speed up, move the levers farther forward. Set throttle lever to the run position. Pull knob up and hold in the choke position. If necessary, pull knob up and hold in choke position. Starter may be damaged if starter is operated for more than 20 seconds at a time: Turn deefe switch to the start position.
The bypass valves must be fully turned clockwise closed during normal vehicle operation. Always lock the park ojhn and remove the key before leaving the machine unattended. Children or bystanders may attempt to move or operate an unattended machine. When the bypass valve is open, the machine will have unrestricted motion.
Do not use hands or johh to clear plugged mower deck or blower assembly. Stored energy can cause blades to rotate. Wait for all moving parts to stop before getting off mznual inspect machine. Remove chute from mower deck or blower assembly. Use recommended John Deere greases to dsere component failure and premature wear. The recommended John Deere greases are effective within an average air temperature range of to degrees C to degrees F.
What’s missing? Tell us about it.
B B If operating outside that temperature range, contact your Servicing dealer for a special-use grease. Engine exhaust fumes contain carbon monoxide and can cause serious illness or death. Do not run an engine in an enclosed area, such as a garage, even with doors or windows opened. Move the machine to an outside area before running the engine. Engine Oil Use oil viscosity based on the expected air temperature range during the period between oil changes.
Single cylinder Briggs and Stratton shown. Check oil level on dipstick. If oil level is low, add oil to bring oil level no higher than FULL mark on dipstick. Install and tighten dipstick. Operating in extreme conditions may require more frequent service intervals: Add oil no higher than FULL mark on dipstick. Begin with approximately 1.
Start and run engine at idle to check for leaks. Fix any leaks before operating. Add oil if necessary. Put drain pan under drain valve Aand loosen drain valve to drain oil into drain pan.
John Deere Z Z Series Zero-Turn Mowers
Clean air intake screen on top of engine and external surfaces with rag, brush, vacuum or compressed air. Inspect the paper filter element D without removing it.
If the paper filter element is hohn or dirty: Dirt and debris can enter the engine through a damaged filter element: Inspect the foam precleaner E without removing it. If the foam precleaner is dirty: Remove it from the filter carefully.
In Canada, replace derre plug with resistor plug only. Replace spark plugs as necessary. Check plug gap B with a wire feeler gauge. To change gap, move the outer electrode. Deeer must be 0. Connect spark plug wire s.
No maintenance is required on this transmission. If you suspect any transmission problems, please contact your authorized dealer. Do not mix oils. Contamination can damage the hydraulic system. Clean thoroughly around reservoir fill cap before opening. If oil level is low, clean area around reservoir cap C.